基于基准有限元模型的箱梁TMD振动控制研究

针对高架桥梁结构引起的振动噪声问题,研究TMD控制箱梁结构振动的特性。为了获得精准的箱梁有限元模型,首先以铁路32 m简支箱梁桥为原型,按10:1的几何相似比设计制作简支箱梁缩尺试验模型,应用ANSYS软件建立初始动力有限元模型;对有限元模型模态分析与试验模型模态测试得到的自由模态信息进行误差分析,并采用基于灵敏度分析的模型修正技术对初始动力有限元模型弹性模量和密度进行修正,得到基准有限元模型,误差确认结果显示修正后的有限元模型更精准地反应箱梁的振动特性;进一步利用基准有限元模型,开展TMD控制简支箱梁桥振动的研究,研究结果表明TMD对于抑制桥梁竖向共振有很好的效果。     

上游静止柱体对圆柱体结构尾激振动的影响

文章运用半隐式特征线分裂算子有限元算法对串列布置的静止上游柱体和下游圆柱的尾激振动问题进行了数值模拟研究。数值结果表明:上游柱体结构的形状、尺寸比(d/D)和折减速度(Ur)三个参数对下游圆柱体结构的动力响应、运动轨迹与涡脱落模态有着显著的影响,且与单圆柱工况相比存在明显区别;随着尺寸比的增大,上/下游柱体结构之间的互扰作用会由流致效应逐渐转变为尾流效应,使得频率特性发生变化,并会导致下游圆柱体结构的振动响应增强;当d/D=0.5和1.0时,下游圆柱体结构的运动轨迹主要为“8”字形;当d/D=1.5时,除了“8”字形外,运动轨迹还会呈现双弯刀形、“双8”字形和不规则形状。通过对流体力系数与位移时程曲线及位移PSD曲线特性进行分析,揭示了其相互作用的内在机理。另外,下游圆柱体结构的尾流场特性也会随参数的变化而变化,其涡脱落模态主要为2S、P+S和2P三种。     

燃机动力学建模中复杂结构处理方法研究

提出了三种以动力学相似为基础的转子动力学建模关键技术,并以某型燃气轮机建模为例,对该关键技术进行了验证。利用三种方法,对该燃气轮机的动力学特性进行研究,并与整机试验结果进行了对比。结果表明,动力学分析的准确程度主要由模型决定,本文所提出的三种建模关键技术能够反映结构的真实特性,可用于具有类似结构的双转子系统。     

Structural safety assessment procedure for membrane-type LNG CCS considering hydroelasticity effect

As environmental regulations have become more onerous, the demand for LNG and LNG carriers has increased. The LNG cargo containment system (LNG CCS) is one of the most important facilities in LNG carriers, and many membrane types of LNG CCS have been developed so far. Traditionally, sloshing model tests are performed and a series of statistical approaches are used to obtain design sloshing pressures. Then, these design loads are utilized to analyze the structural safety of LNG CCS. In the sloshing model test, the flat and almost rigid plate is used as the LNG CCS instead of a real model, and thus, the hydroelasticity effect cannot be considered. In the present research, the effect of hydroelasticity on sloshing pressure was investigated in a fluid-structure interaction simulation. A wet drop simulation was conducted, and its results subsequently were compared with wet drop experimental test results to ensure their validity. Then, two types of structure model, namely a flat-rigid plate model and a flat-flexible CCS model, were generated to investigate the effect of hydroelasticity. Also, a fluid hitting analysis model was devised to realize the sloshing phenomenon, and the two generated structure models were applied as the structure domain in the analysis. In the fluid hitting simulations, it was found that the hydroelasticity effect on sloshing pressure is significant. Thus, correction factors, which are quantitative values of the effect of hydroelasticity, were derived (and are proposed herein). Finally, a structural safety assessment procedure for consideration of the hydroelasticity effect was derived (and is suggested herein).     

某磁浮大跨斜拉桥竖向刚度限值研究

以某磁浮轨道交通(40+80+228+228+80+40)m大跨钢箱梁斜拉桥为研究对象,采用有限元软件ANSYS和多体动力学软件UM分别建立桥梁和磁浮列车模型。基于车桥耦合振动方法,针对2列磁浮列车相向行驶并在主跨跨中交会的最不利情形,进行列车以不同速度通过桥梁时不同梁高下车桥系统的动力响应及磁浮大跨桥梁的竖向刚度限值研究。结果表明:磁浮列车的竖向动力响应随车速的增大而显著增大,时速从40 km增大到140 km时,列车竖向动力响应增幅达到120%以上;车体竖向加速度和Sperling指标不是桥梁结构刚度限值的控制因素;磁浮列车的悬浮间隙对梁体刚度变化较为敏感,随着梁体刚度逐步增大,悬浮间隙的波动变小,梁体挠跨比减小约25%,悬浮间隙波动减小幅度达35%,悬浮间隙可作为中低速磁浮大跨桥梁结构刚度限值的控制指标;梁体挠跨比1/3015可作为磁浮大跨桥梁的竖向刚度限值。     

冲压机械振动对高铁桥梁及行车动力影响分析

高速铁路桥梁的平顺性和稳定性对运营列车的平稳性和安全性有很大影响。为研究冲压机械产生的外部振动激励对高铁桥梁的影响,首先通过对此机械引起的地面振动进行实测,并结合有限元分析软件,确定最大冲击荷载作用下产生的地面振动及传播至桥墩处的振动;然后通过建立列车-轨道-桥梁耦合动力学模型,将桥墩处的地面振动作为激励输入,分析列车以不同速度通过时车辆、桥梁动力学响应。结果表明:地面冲击振动有限元模型计算结果与实测结果基本相符,验证了模型的可靠性;地面振动对桥梁响应会产生一定的影响,距振源50 m处地面振动对桥梁所产生的影响较距振源80 m处(桥墩处)的大,但对运行车辆的影响很小;随着车速由250 km/h至350 km/h,车辆及桥梁各结构的动态响应均有所增大,但都未超出安全限值。因此,冲压机械冲击作用导致的地面振动对列车-轨道-桥梁系统动态服役性能影响非常有限。     

基于完全耦合算法的绕水翼流固耦合特性研究

基于完全耦合算法对绕二维NACA0009水翼流固耦合特性进行了数值模拟研究。采用Theodorsen模型和Munch模型对刚性和弹性水翼的水弹性响应进行了数值计算,分析了流体与结构的相互作用关系,研究了影响结构水弹性响应和流固耦合特性的因素。研究结果表明:考虑了流体黏性的Munch模型与基于势流理论的Theodorsen模型对气动弹性响应的数值计算结果基本一致,而Theodorsen模型由于没有考虑流体黏性在一定程度上低估了结构的水弹性响应。结构的惯性、阻尼和刚度力矩与流体的相应附加载荷均处于同一数量级,故流体与结构的相互作用不可忽略,尤其对于弹性水翼,流体的惯性、附加阻尼作用增大,流固耦合算法的数值稳定性对流固耦合特性的计算结果影响将更大。外部激励频率为非共振频率时,结构的刚度作用是影响水弹性响应的主要因素,外部激励频率为共振频率时,流体的附加阻尼和附加刚度作用减弱,除结构的刚度作用外,流体与结构的惯性作用对水弹性响应和流固耦合特性的影响也较大。     

Layout optimization of an inertial energy harvester for miniature underwater mooring platforms

Comprehensive analyses of the layout influence on power performance of a low-frequency miniature horizontal-pendulum-type inertial energy harvester for underwater mooring platforms are presented in this article. The mathematical models are obtained utilizing the Newton-Euler method. The power performance is evaluated by simulations over different parameters, such as damping, excitation frequency, and layout position. Simulation results indicate that the harvester can extract energy from low-frequency excitations over the range of 0.1 Hz–0.4 Hz, and maximum output power can reach to 0.7 W under excitation frequency f = 0.4 Hz. Different layout positions influence the energy harvesting performance of the harvester dramatically. Changing the layout position to positive value can enhance and broaden the power performance. The amplitude responses with different layout positions do not show resonant characteristics, even near the natural frequency of the harvester, due to large amplitude vibrations and strong nonlinear characteristic. As excitation frequency f = 0.4 Hz, there is a zero output power point appears at layout position d = −1.3 m. Moreover, the harnessed power has a quadratic relationship with the layout position value.     

Centrifuge modelling of pipe-soil interaction in clay with crust layer

Seabed in regions, such as the Gulf of Guinea and North West Shelf of Australia, may exhibit a crust layer where the undrained shear strength can be an order of magnitude higher than that of the immediately underlying sediment. This can complicate design of steel catenary risers, where fatigue depends on the cyclic vertical stiffness of the pipe-soil interaction. Potential punch-through of the riser into the underlying soft soil may invalidate design assumptions based on the pipe-soil stiffness within the crust layer. The long-term evolution of pipe-soil stiffness within the crust layer, which exhibits similar properties to an over-consolidated soil, is also poorly understood. This paper describes centrifuge model tests undertaken in a clay sample with a crust layer, simulating the punch-through process of a pipe under load control and investigating the pipe-soil stiffness during long-term cyclic loading tests under displacement control. Results confirm that the potential for punching-through the crust layer depends strongly on the relative ratio of pipe diameter to crust layer thickness. The long-term evolution of pipe-soil stiffness showed a steady increase after an initial remoulding stage in contractile soils (normally consolidated and lightly over-consolidated), but a steady reduction in the heavily over-consolidated, more dilatant, crust. The magnitude of pipe-soil stiffness changes (during both remoulding and reconsolidation) is governed by the over-consolidation ratio of the soil and the amplitude of the cyclic displacements. This study provides insights on the relevant cyclic stiffness to consider when assessing SCR fatigue life in over-consolidated soils and soils exhibiting a superficial crust layer.